Find your code

What a Power Reset Really Does to an Appliance, and How Long to Wait

Unplugging an appliance is the most common advice online and the least understood. What a power reset clears, what it cannot fix, and why Bosch, LG and Samsung publish different waiting times.

By ApplianceCodeHQ Editorial Updated

In this guide
  1. What a reset does and what it does not
  2. How long to wait: why the numbers differ
  3. Three kinds of reset that are easy to confuse
  4. When a reset is the wrong first move
  5. A sensible order
  6. Frequently asked questions

Search for almost any appliance fault and the first line of advice is the same: unplug it, wait, plug it back in. Sometimes that works, often it does not, and almost nobody explains why. A power reset is not a repair. It restarts the electronics that run the appliance, and that is useful in a narrow set of situations. Outside them it can cost you the one piece of evidence that would have pointed to the real problem. This article explains what a reset does, what the manufacturers actually publish about timing, and how to decide whether to do one at all.

What a reset does and what it does not

Washers, dryers, dishwashers and refrigerators are controlled by an electronic board that keeps a small amount of state in memory: the current cycle position, door and sensor readings and the last fault it detected. Cutting power lets that board start from a clean state. Samsung’s support guidance on dishwasher resets puts it plainly: a reset clears the error codes stored in memory and can help with minor electronic glitches, such as those that follow a power outage. It then adds the limits. A reset will not fix a door that does not close fully, an installation problem that stops the dishwasher turning on, or a drain problem, and resetting without fixing the underlying cause will likely bring the code back.

That is the model to keep in mind. A fault that lives in the board’s memory goes away with a reset. A fault that lives in the appliance, such as a blocked filter, a kinked hose, a loose door latch or low supply voltage, is detected again as soon as the cycle runs. A code that returns after a reset is useful information: it tells you the sensor is genuinely reporting something.

How long to wait: why the numbers differ

There is no universal waiting time, and the manufacturers do not pretend there is. Their US pages give different figures for different appliances and sometimes for different codes on the same appliance. The table collects what the pages we cite say; the exact manual for your model takes precedence.

Published power-interruption times in US manufacturer guidance
Brand and situationWhat the page says
Samsung dishwasher, general reset Unplug or switch off at the breaker, wait 1 to 5 minutes, restore power
Samsung dishwasher 7E, after correcting the cause Two-minute power interruption
Bosch dishwasher, heat-pump codes such as E09 and E21 Breaker off for 30 seconds, then call Bosch support if the code returns
Bosch dishwasher, general reset Off for about a minute, back on, then a short empty cycle
LG washer, Ed5 communication code Unplug for 60 seconds
LG dryer, PS voltage code Breaker reset for 10 seconds, with the outlet and cord checked
LG dryer, tE1 and tE3 thermistor codes Unplug or trip the breaker, hold Start/Pause for 5 seconds while unpowered, restore power and run a cycle
Samsung dryer, AC communication 60 seconds
Samsung dryer, 3C and HC2 2 to 3 minutes, then service if the code returns

The spread, from 10 seconds to 5 minutes, is not a contradiction. Each figure is tied to a particular code and a particular control design, and none of the pages claims that a longer wait is better in general. The practical reading: use the time in the instructions for your code or model, and when the instructions give none, a minute is the middle of the published range. Do not treat a longer wait as a stronger reset.

Three kinds of reset that are easy to confuse

A power reset (unplug or breaker) is different from the other things people also call a reset. Cancelling a cycle is one: Bosch’s guidance for its dishwashers is to hold Reset or Start for about four seconds, after which the residual water is pumped out in about a minute and the cycle ends. That ends a program but does not clear the stored fault. LG’s thermistor procedure goes a step further: with the dryer unplugged or the breaker tripped, hold Start/Pause for five seconds, then restore power. Pressing a button with no power applied discharges what remains in the control and is an instruction for that code, not a habit to apply to every appliance. Finally, network or settings resets on connected models erase Wi-Fi information or saved preferences and have nothing to do with fault codes.

When a reset is the wrong first move

A reset erases the stored error history. Samsung’s guidance is to complete the relevant troubleshooting first and reset afterwards, because some codes stay displayed even after the problem is fixed and the reset is simply the way to clear them. Following that order has a second benefit: if you note the code and the conditions first, a technician later gets a precise description instead of “it stopped and I rebooted it”.

Other cases where a reset is not the answer: a code that names a supply voltage problem (Bosch E27 points to low house supply voltage and asks for an electrician to check the incoming voltage if it recurs), anything involving burning smell, smoke, tripped breakers or hot plugs, and any fault on a refrigerator that holds food. For Samsung refrigerator ice-maker codes the support pages say to preserve the error and not to reset it. Resetting these appliances does not repair a failed part and may only delay a safe decision.

A sensible order

  1. Write down what you see

    Record the exact code, any suffix, what the appliance was doing and the model number. Take a photo of the display.

  2. Check the cause the code names

    Door closed, filter clean, hoses unkinked, supply valve open. A reset cannot do these for you.

  3. Reset only as the instructions say

    Use the method and time given for your code or model; for a general reset a minute is typical in the published range.

  4. Run a short test

    Start a short, empty cycle and watch for the same code. If it returns, stop resetting.

  5. Request service

    Give the technician the code, the steps you took and the result. Do not open panels or work on wiring yourself.

Frequently asked questions

Does unplugging an appliance save it from a fault?

It only restarts the electronics. If the cause is physical or an incoming voltage problem, the fault comes back.

Is flipping the breaker the same as unplugging?

The manufacturers use both interchangeably for a power reset. Bosch and LG name the breaker in several procedures, which also helps when the plug is hard to reach.

Will a reset void the warranty?

The pages we cite describe resets as an ordinary owner step. They do not say it affects coverage, but your warranty terms are the place to check.

Can I reset a refrigerator to clear a code?

Only if the manual or the code’s support page says so. Some refrigerator pages tell you to preserve the error and request service instead.

Sources: According to the manufacturer; this is not an independent diagnosis and times apply only to the codes and models named.
Samsung US: When to reset a dishwasher — checked 2026-11-03.
Bosch US: Dishwasher Error Codes — checked 2026-11-03.
Bosch US: How to Reset the Dishwasher or Stop a Wash Cycle — checked 2026-11-03.
LG USA: Dryer Error Code List — checked 2026-11-03.
LG USA: Front Load Washer Error Code List — checked 2026-11-03.
Samsung US: Dryer displays an error code — checked 2026-11-03.
Samsung US: WaterWall reflector error 7E — checked 2026-11-03.

Seen a code you do not recognise?

Start from the site-wide code index and match brand, appliance and exact letters.

Open the code index

Related guides

Related codes & guides

Guide

Symptom guide

How to Reset a Bosch Dishwasher

Two different Bosch resets: cancel a running cycle with the Reset or Start button held about 4 seconds, or reset power…