Find your code

How to Reset a Bosch Dishwasher

Two different Bosch resets: cancel a running cycle with the Reset or Start button held about 4 seconds, or reset power at the breaker for an error code. When to stop resetting.

By ApplianceCodeHQ Editorial Updated

In this guide
  1. Which reset do you need?
  2. Cancel a running cycle and drain
  3. Reset power for an error code
  4. Frequently asked questions

People say “reset” for two different things on a Bosch dishwasher. One is cancelling a cycle that is already running: the dishwasher pumps out the water and stops. The other is a power reset to clear an error code, which Bosch describes as switching the breaker off for 30 seconds. They solve different problems, and neither repairs a fault that keeps returning. Choose the one that fits your situation, do it once, and let the result tell you what to do next.

Which reset do you need?

Bosch US guidance; check your manual for the exact button label
SituationReset to use
You chose the wrong program or need to stop the cycle Cancel and drain: hold Reset or Start about 4 seconds
The display shows an error code with a reset instruction (E09, E21, E27 and others) Power reset at the breaker for 30 seconds
The display shows h01, h02 and so on No reset: it is the delay-start timer, not an error
Code E14, E15 or E23 No reset in Bosch’s list: follow that code’s action and contact support

Cancel a running cycle and drain

  1. Reach the controls carefully

    If the buttons are on the top edge of the door, open it slowly: Bosch warns that hot water or steam may escape during or after a cycle.

  2. Hold Reset or Start

    Press and hold the button marked Reset 4 Sec. or Start for about 4 seconds.

  3. Wait while it drains

    The dishwasher pumps out the remaining water. Bosch says this takes about a minute.

  4. Switch off

    When draining has finished, open the door and press On/Off. You can now choose a new program.

Button names differ between series. The SHP78CM5N manual, for example, shows the cancel control as a symbol rather than the word Reset, and the display shows 00h:01m while the water is pumped out. If your panel has neither label, look for “Terminating the wash cycle” or a similar section in your own Use and Care manual rather than trying button combinations.

Reset power for an error code

For many electronic and heat-pump codes, Bosch’s US list starts with the same instruction: cut power at the breaker for 30 seconds, restore it and try again; if the code returns, call Bosch Customer Support. For E27 (house power supply too low) the follow-up is an electrician rather than Bosch. Bosch’s general advice for a dishwasher that seems stuck is similar — power off for about a minute, back on, then a short test cycle with no dishes.

Frequently asked questions

Does cancelling a cycle clear an error code?

Not necessarily. Cancel-and-drain stops a program; Bosch’s instruction for error codes is the breaker reset.

Why does my Bosch show h01?

Bosch lists h01, h02 and so on as the delay-start timer. Use the + or – buttons until h:00 shows to cancel the delay.

Is there a factory reset?

Some connected models describe a factory reset in the manual or the Home Connect app. It is a settings reset, not a repair.

Sources: According to the manufacturer; this is not an independent diagnosis.
Bosch US: How to Reset the Dishwasher — checked 2026-10-26.
Bosch US: Dishwasher Error Codes — checked 2026-10-26.
Bosch: Use and Care Manual SHP78CM5N, document 9001641455 A — checked 2026-10-26.

Bosch dishwasher error codes

Which codes allow a breaker reset and which go straight to service.

Open the reference

Codes that start with a reset

Bosch codes where one power reset is the first step.

Related codes & guides

Chart

Dishwashers

Bosch Dishwasher Error Codes

Every Bosch dishwasher code we cover, from E09 to E27: what each one means, which allow a breaker reset, which need a…