Error code
LG washer · UE
LG washer UE Error Code
Unbalanced load — the drum can't spin evenly.
Easy fix · 10–20 minUse Samsung washer calibration with an empty tub and model-specific controls. Cb/C6 is a calibration status, while continuing spin faults need separate checks.
Calibration adjusts a Samsung washer’s load-weight detection. It is a setup function, not a promise to repair every vibration or spin complaint. Cb or C6 can identify calibration mode on applicable washers. Save any actual fault code separately before selecting a setup procedure; an error should not be renamed a calibration message just because the drum is moving slowly.
Samsung’s general installation guidance calls for calibration with an empty washer after installation or relevant adjustments. Its named US page for WA54R7200A* and WA50R5200A* top-load series supplies a specific control sequence. The example below is restricted to those series. Other panels may use different buttons or a settings menu; the exact US owner’s manual takes precedence.
| Requirement | Why it matters |
|---|---|
| Empty tub or drum | Laundry changes the calibration conditions; remove it before starting. |
| Completed, safe installation | Calibration does not level an appliance or correct an unsafe hose or electrical connection. |
| Matching model controls | A button combination from another series may operate a different function. |
| No active hazardous condition | Do not run setup with severe movement, leakage, smoke or damaged parts. |
Remove all laundry and compare the complete model number to the named-series support page.
Power on, then hold Temp. and Delay End together for three seconds, as specified for these series.
Use Start/Pause (Hold to Start). Samsung describes about two minutes of tub rotation for this example.
The named-series page describes a 0 display followed by automatic power-off. Do not treat another model’s display as a failure solely because it differs.
Record whether calibration completed under the correct empty conditions. If the original symptom returns, use its actual code or symptom guide. Completion does not establish that bearings, suspension, motor or water delivery are healthy. Likewise, no displayed gallons-per-cycle figure can be derived from this procedure; water-cost tools need a separate documented or measured input.
No. Samsung requires an empty washer for correct weight calibration.
No. That sequence is restricted here to the two named series; use your model manual.
Do not assume it will. A reported sensor or motor fault needs its own manufacturer guidance.
Sources: According to the manufacturer for appliance behavior; this is not an independent diagnosis.
Samsung US: Calibration — WA54R7200A* / WA50R5200A* — checked 2026-10-22.
Samsung US: Install a washing machine in your home — checked 2026-10-22.
Samsung US: Washing machine information and error codes — checked 2026-10-22.
Keep the model and complete display with every procedure.
Error code
LG washer · UE
Unbalanced load — the drum can't spin evenly.
Easy fix · 10–20 min
Error code
Error code
LG washer · IE
Water inlet error — the tub isn't filling.
Easy fix · 10–20 min
Error code
Samsung washer · LC
Water level or leak error — water is detected where it doesn't belong.
ModerateWashers
Browse eighteen LG washer code pages, including distinct Ed1/Ed2 detergent warnings and ezDispense Ed5, with model…
Guide
Symptom guide
Water remains in the washer? Match the drain code and model before inspecting a hose or using an owner-accessible filter…
Washers
One chart for the common washer problems — drain, fill, unbalanced load, door, leak — and the code LG, Samsung and…
Error code
LG washer · dE
The door has not closed or locked as required.
Check model first
Error code
LG washer · LE
The tub cannot spin; LG identifies overload or an object in the tub as possible reasons.
Check model first
Error code
Error code
LG washer · tE
Heating error; LG associates it with the thermistor that senses temperature.
Call a pro
Error code
Error code
Samsung washer · 4C
Water is not entering the washer correctly.
Check model first
Error code
Samsung washer · 5C
Water is draining too slowly or is not draining.
Check model first
Error code
Samsung washer · dC
Model-dependent: a door error or an unbalanced-load error.
Check model first
Error code
Samsung washer · Ub
An unbalanced load prevented the cycle from completing.
Check model first
Error code
Whirlpool washer · F8 E1
The washer senses insufficient incoming water flow.
Check model first
Error code
Whirlpool washer · F9 E1
The drain operation is taking longer than expected.
Check model first
Error code
Whirlpool washer · F5 E2
The door is not locking correctly.
Check model firstWashers
Browse fourteen Samsung washer code pages with AC communication, 3C motor and tC sensing, model-dependent 3E meanings…
Washers
Compare thirteen Whirlpool front-load code pages for water, doors, balance, foam and dispenser messages, with exact…
Guide
Symptom guide
Separate a drain problem, an unbalanced load and a door warning before treating a washer that will not spin as a…
Error code
LG washer · Sud
The washer has detected too much foam and is managing an oversudsing condition.
Check model first
Error code
LG washer · PF
Power was interrupted during operation; the display does not identify why the supply was lost.
Check model first
Error code
LG washer · CE
An overcurrent condition has been detected in the motor’s electrical circuit.
Call a pro
Error code
Samsung washer · OC
The washer reports an overflow condition: too much water is detected.
Call a pro
Error code
Samsung washer · 4C2
The cold-water supply is unexpectedly hot; Samsung identifies reversed hot and cold connections.
Check model first
Error code
Samsung washer · SUd
Excessive suds were detected; the washer pauses to let the foam settle before continuing.
Check model first
Error code
Whirlpool washer · F5 E1
Whirlpool identifies this front-load entry as a door-switch condition.
Check model first
Error code
Whirlpool washer · F5 E3
The cited Whirlpool front-load guidance says the door is not locking properly.
Check model first
Error code
Whirlpool washer · F7 E1
A motor-speed sensing error: the selected cycle speed is not being achieved.
Check model first
Error code
Whirlpool washer · Sud / Sd
Excess suds are interfering with the wash or spin, so the washer adds rinsing and pauses.
Check model first
Guide
Symptom guide
Compare LG Sud, Samsung SUd and Whirlpool Sud/Sd without assuming the same pause, cleaning cycle or dispenser…
Guide
Symptom guide
A locked front-load door may be protecting against water, heat or drum movement. Preserve the code and use the exact…
Error code
LG washer · dHE
LG identifies a dry-function error on applicable washer-dryer equipment.
Check model first
Error code
LG washer · AE
The covered LG front-load entry reports internal leakage and activation of the leak-protection system.
Call a pro
Error code
LG washer · SE
LG’s front-load support describes SE as a sensor error requiring service if the limited restart does not resolve it.
Call a pro
Error code
Whirlpool washer · F0 E1
A load is detected while the Clean Washer maintenance cycle is selected; Whirlpool also lists rL for this condition.
Check model first
Error code
Whirlpool washer · F0 E5
The covered front-load washer reports an off-balance load, which can extend the cycle or reduce spin speed.
Check model first
Error code
Whirlpool washer · F8 E2
Whirlpool identifies a problem with the front-load washer’s dispenser system.
Check model first
Error code
Whirlpool washer · F8 E3
The washer reports an overflow condition involving too much water or foam.
Call a pro
Error code
Whirlpool washer · dET
The detergent dispenser cartridge is not detected on applicable cartridge-equipped front-load washers.
Check model first
Error code
Whirlpool washer · Int
The cycle was paused or canceled; Int can remain while the washer stops spinning and drains.
Check model first
Guide
Symptom guide
Separate normal load sensing from a washer that will not fill. Compare LG, Samsung and Whirlpool supply codes, safe…
Guide
Symptom guide
Samsung washer CL or locked buttons can indicate Child Lock. Use the model’s labeled controls, distinguish a door…
Guide
Symptom guide
Use LG Tub Clean, Samsung Self Clean or Whirlpool Clean Washer with an empty drum, the correct model instructions and…
Error code
LG washer · HE
According to LG, HE reports a heater error on the front-load models covered by its US guide.
Check model first
Error code
LG washer · vS
According to LG, vS concerns the vibration sensor; the display can resemble u5 or uS.
Check model first
Error code
Samsung washer · bE2
Samsung places bE2 in its stuck-button group, but BE2/8E2 means a MEMS sensor error on some models.
Check model first
Error code
Samsung washer · 9C1
According to Samsung, 9C1 belongs to the washer electrical-supply irregularity group.
Call a pro
Error code
Samsung washer · ddC
According to Samsung, ddC or dC3 means the Add Door is not detected as closed and locked.
Check model first
Guide
Symptom guide
Clear Samsung auto-dispenser refill messages at the correct wash or rinse stage. Check liquid compartments, drawer…
Guide
Symptom guide
Samsung washer dn means an update is downloading. Keep power on, record elapsed time and use the washer-specific support…
Guide
Symptom guide
Check Whirlpool Load & Go by washer design, liquid type and dosing mode. Keep top-load controls separate from front-load…
Guide
Symptom guide
Whirlpool front-load LoC or LC can be a Control Lock setting. Use the labeled model controls and distinguish it from…
Error code
LG washer · Ed1 / Ed2
LG identifies Ed1 and Ed2 as detergent-dispensing warnings, with different pump conditions reported.
Check model first
Error code
LG washer · Ed5
LG identifies Ed5 as a communication problem involving the automatic detergent dispenser and its control system.
Check model first
Error code
Samsung washer · AC
Samsung lists AC as a washer communication error; the exact model determines the affected system.
Check model first
Error code
Samsung washer · 3C
Samsung identifies washer 3C as a motor error. It does not by itself identify a failed motor or sensor.
Check model first
Error code
Samsung washer · tC
Samsung lists washer tC, tE and tE1 in its temperature-sensor error group.
Check model first
Guide
Symptom guide
Clean an LG ezDispense drawer using the matching model instructions. Distinguish OPn closure, dcL nozzle cleaning and…
Guide
Symptom guide
Read Samsung washer blinking lights with the exact panel and model. Separate fault patterns from Self Clean reminders…
Thank you! Your feedback helps us make this page better.
Could not send. Please try again.