Find your code

Whirlpool Washer Error Codes

Compare thirteen Whirlpool front-load code pages for water, doors, balance, foam and dispenser messages, with exact F/E combinations and model limits.

By ApplianceCodeHQ Editorial Updated

This Whirlpool US front-load index now links thirteen code pages. Keep both F and E segments. F8 E1 concerns incoming flow, F8 E2 the dispenser and F8 E3 overflow; similar prefixes do not make their procedures interchangeable. F0 E1/rL belongs to an occupied Clean Washer cycle, F0 E5 to imbalance, dET to cartridge detection and Int to an interrupted cycle. The current US F5 E3 entry still requires its model-specific locking interpretation.

Model and appliance scope

US front-load washers in Whirlpool Product Help. Top-load washers, stacked laundry centers and dishwashers can require different entries. No specific model-number compatibility is asserted without that model’s manual.

Whirlpool Washer code reference

CodeMeaningDifficultyFix
F8 E1 The washer senses insufficient incoming water flow. Check model first F8 E1 page →
F9 E1 The drain operation is taking longer than expected. Check model first F9 E1 page →
F5 E2 The door is not locking correctly. Check model first F5 E2 page →
F5 E1 Whirlpool identifies this front-load entry as a door-switch condition. Check model first F5 E1 page →
F5 E3 The cited Whirlpool front-load guidance says the door is not locking properly. Check model first F5 E3 page →
F7 E1 A motor-speed sensing error: the selected cycle speed is not being achieved. Check model first F7 E1 page →
Sud / Sd Excess suds are interfering with the wash or spin, so the washer adds rinsing and pauses. Check model first Sud / Sd page →
F0 E1 A load is detected while the Clean Washer maintenance cycle is selected; Whirlpool also lists rL for this condition. Check model first F0 E1 page →
F0 E5 The covered front-load washer reports an off-balance load, which can extend the cycle or reduce spin speed. Check model first F0 E5 page →
F8 E2 Whirlpool identifies a problem with the front-load washer’s dispenser system. Check model first F8 E2 page →
F8 E3 The washer reports an overflow condition involving too much water or foam. Call a pro F8 E3 page →
dET The detergent dispenser cartridge is not detected on applicable cartridge-equipped front-load washers. Check model first dET page →
Int The cycle was paused or canceled; Int can remain while the washer stops spinning and drains. Check model first Int page →

Safe first checks

  1. Preserve the entire code

    Photograph alternating segments if the display shows them separately. Include the full model number in a service request.

  2. Check the relevant external path

    F8 E1 leads to water-supply checks, F9 E1 to drain installation and detergent, and F5 E2 to normal door closure.

  3. Respect the model’s drain routine

    The F8 E1 guidance describes temporarily unresponsive controls while draining. Do not force the door or interrupt the routine repeatedly.

Frequently asked questions

Are F5 E1, F5 E2 and F5 E3 interchangeable?

No. Each complete combination has its own page and model scope. The current F5 E3 front-load source describes improper locking; follow the exact manual if its definition differs.

Does this chart apply to a Whirlpool dishwasher?

No. These entries are explicitly for US front-load washers.

Does F7 E1 prove the motor is broken?

No. The documented owner checks include installation and load. Persistent speed errors require diagnosis.

Sources: According to the manufacturer; model-specific instructions take precedence.
Whirlpool US Product Help: Front-load washer error codes — checked 2026-10-22.
Whirlpool US Product Help: F5 E2 — Error Code — checked 2026-10-22.
Whirlpool US Product Help: Front-load washer door will not open — checked 2026-10-22.
Whirlpool US: F5 E1 — Front Load Washer — checked 2026-10-22.
Whirlpool US: F5 E3 — Front Load Washer — checked 2026-10-22.
Whirlpool US: F7 E1 — Front Load Washer — checked 2026-10-22.
Whirlpool US: SUD or Sd — Front Load Washer — checked 2026-10-22.
Whirlpool US: F0 E1 or rL — Front Load Washer — checked 2026-10-22.
Whirlpool US: F0 E5 — Front Load Washer — checked 2026-10-22.
Whirlpool US: F8 E2 — Front Load Washer — checked 2026-10-22.
Whirlpool US: F8 E3 — Front Load Washer — checked 2026-10-22.
Whirlpool US: dET — Front Load Washer — checked 2026-10-22.
Whirlpool US: Int — Error Code — checked 2026-10-22.

Symptom guides and related references

Continue with the relevant symptom or compare a repair quote after diagnosis.

Foam and locked-door symptoms

Maintenance and dispenser messages

Dispenser operation and lock settings

Load & Go controls differ across top-load and front-load designs; the code index above retains its front-load scope.

Related codes & guides

Error code

LG washer · UE

LG washer UE Error Code

Unbalanced load — the drum can't spin evenly.

Easy fix · 10–20 min
Error code

LG washer · OE

LG washer OE Error Code

Drain error — water isn't draining.

Easy fix · 20–30 min
Error code

LG washer · IE

LG washer IE Error Code

Water inlet error — the tub isn't filling.

Easy fix · 10–20 min
Error code

Samsung washer · LC

Samsung washer LC Error Code

Water level or leak error — water is detected where it doesn't belong.

Moderate
Chart

Washers

LG Washer Error Codes

Browse eighteen LG washer code pages, including distinct Ed1/Ed2 detergent warnings and ezDispense Ed5, with model…

Chart

Washers

Washer Error Codes by Brand

One chart for the common washer problems — drain, fill, unbalanced load, door, leak — and the code LG, Samsung and…

Error code

LG washer · dE

LG washer dE Error Code

The door has not closed or locked as required.

Check model first
Error code

LG washer · LE

LG washer LE Error Code

The tub cannot spin; LG identifies overload or an object in the tub as possible reasons.

Check model first
Error code

LG washer · PE

LG washer PE Error Code

LG reports a problem with the water-level sensor.

Call a pro
Error code

LG washer · tE

LG washer tE Error Code

Heating error; LG associates it with the thermistor that senses temperature.

Call a pro
Error code

Samsung washer · dC

Samsung washer dC Error Code

Model-dependent: a door error or an unbalanced-load error.

Check model first
Error code

Samsung washer · Ub

Samsung washer Ub Error Code

An unbalanced load prevented the cycle from completing.

Check model first
Chart

Washers

Samsung Washer Error Codes

Browse fourteen Samsung washer code pages with AC communication, 3C motor and tC sensing, model-dependent 3E meanings…

Error code

LG washer · Sud

LG Washer Sud Error Code

The washer has detected too much foam and is managing an oversudsing condition.

Check model first
Error code

LG washer · PF

LG Washer PF Error Code

Power was interrupted during operation; the display does not identify why the supply was lost.

Check model first
Error code

LG washer · CE

LG Washer CE Error Code

An overcurrent condition has been detected in the motor’s electrical circuit.

Call a pro
Error code

Samsung washer · OC

Samsung Washer OC Error Code

The washer reports an overflow condition: too much water is detected.

Call a pro
Error code

Samsung washer · 4C2

Samsung Washer 4C2 Error Code

The cold-water supply is unexpectedly hot; Samsung identifies reversed hot and cold connections.

Check model first
Error code

Samsung washer · SUd

Samsung Washer SUd Error Code

Excessive suds were detected; the washer pauses to let the foam settle before continuing.

Check model first
Error code

Whirlpool washer · F5 E1

Whirlpool Washer F5 E1 Error Code

Whirlpool identifies this front-load entry as a door-switch condition.

Check model first
Error code

Whirlpool washer · F5 E3

Whirlpool Washer F5 E3 Error Code

The cited Whirlpool front-load guidance says the door is not locking properly.

Check model first
Error code

Whirlpool washer · F7 E1

Whirlpool Washer F7 E1 Error Code

A motor-speed sensing error: the selected cycle speed is not being achieved.

Check model first
Error code

Whirlpool washer · Sud / Sd

Whirlpool Washer Sud / Sd Error Code

Excess suds are interfering with the wash or spin, so the washer adds rinsing and pauses.

Check model first
Error code

LG washer · dHE

LG Washer dHE Error Code

LG identifies a dry-function error on applicable washer-dryer equipment.

Check model first
Error code

LG washer · AE

LG Washer AE Error Code

The covered LG front-load entry reports internal leakage and activation of the leak-protection system.

Call a pro
Error code

LG washer · SE

LG Washer SE Error Code

LG’s front-load support describes SE as a sensor error requiring service if the limited restart does not resolve it.

Call a pro
Error code

Whirlpool washer · F0 E1

Whirlpool Washer F0 E1 Error Code

A load is detected while the Clean Washer maintenance cycle is selected; Whirlpool also lists rL for this condition.

Check model first
Error code

Whirlpool washer · F0 E5

Whirlpool Washer F0 E5 Error Code

The covered front-load washer reports an off-balance load, which can extend the cycle or reduce spin speed.

Check model first
Error code

Whirlpool washer · F8 E2

Whirlpool Washer F8 E2 Error Code

Whirlpool identifies a problem with the front-load washer’s dispenser system.

Check model first
Error code

Whirlpool washer · F8 E3

Whirlpool Washer F8 E3 Error Code

The washer reports an overflow condition involving too much water or foam.

Call a pro
Error code

Whirlpool washer · dET

Whirlpool Washer dET Error Code

The detergent dispenser cartridge is not detected on applicable cartridge-equipped front-load washers.

Check model first
Error code

LG washer · HE

LG Washer HE Error Code

According to LG, HE reports a heater error on the front-load models covered by its US guide.

Check model first
Error code

LG washer · vS

LG Washer vS Error Code

According to LG, vS concerns the vibration sensor; the display can resemble u5 or uS.

Check model first
Error code

Samsung washer · bE2

Samsung Washer bE2 Error Code

Samsung places bE2 in its stuck-button group, but BE2/8E2 means a MEMS sensor error on some models.

Check model first
Error code

Samsung washer · 9C1

Samsung Washer 9C1 Error Code

According to Samsung, 9C1 belongs to the washer electrical-supply irregularity group.

Call a pro
Error code

Samsung washer · ddC

Samsung Washer ddC Error Code

According to Samsung, ddC or dC3 means the Add Door is not detected as closed and locked.

Check model first
Error code

LG washer · Ed1 / Ed2

LG Washer Ed1 / Ed2 Error Code

LG identifies Ed1 and Ed2 as detergent-dispensing warnings, with different pump conditions reported.

Check model first
Error code

LG washer · Ed5

LG Washer Ed5 Error Code

LG identifies Ed5 as a communication problem involving the automatic detergent dispenser and its control system.

Check model first
Error code

Samsung washer · AC

Samsung Washer AC Error Code

Samsung lists AC as a washer communication error; the exact model determines the affected system.

Check model first
Error code

Samsung washer · 3C

Samsung Washer 3C Error Code

Samsung identifies washer 3C as a motor error. It does not by itself identify a failed motor or sensor.

Check model first
Error code

Samsung washer · tC

Samsung Washer tC Error Code

Samsung lists washer tC, tE and tE1 in its temperature-sensor error group.

Check model first