Find your code

Whirlpool washer F9 E1 Error Code

By ApplianceCodeHQ Editorial Updated

F9 E1

What it means

The drain operation is taking longer than expected.

Check model first

Jump to the fix

Applies to these models and systems

Whirlpool US front-load washer guidance. Do not use this washer meaning for a dishwasher or assume it covers every top loader. Hose requirements and filter access must come from the exact model manual.

Whirlpool washer F9 E1 Error Code

What F9 E1 means

A long drain is an observed condition, not a pump replacement instruction. Record whether it started after moving the washer or changing detergent. Keep the complete F9 E1 display when asking for help; dropping either part can lead to the wrong troubleshooting entry.

What the manufacturer identifies

Documented conditions; no failure probabilities assigned
ConditionWhat it means for your next step
Restricted or incorrectly installed drain hose Whirlpool names kinks or blockage and calls for the drain-hose form and correct standpipe installation.
Excess suds The manufacturer says suds can delay drainage and calls for HE detergent.

Safe checks before a repair

  1. Stop before owner inspection

    Disconnect power from a dry location. If the tub contains hot water, let it cool and keep the door closed.

  2. Inspect the accessible hose

    Look for crushing or sharp bends without disconnecting a full hose. Compare the standpipe setup with your model’s installation instructions.

  3. Review detergent use

    Confirm the product is HE detergent and follow its dose instructions. Do not add more detergent to a stalled load.

  4. Check the manual for filter access

    Use a filter-cleaning procedure only if the manual identifies an owner-accessible filter. Do not remove the cabinet to reach a pump.

Frequently asked questions

Does F9 E1 prove the drain pump is bad?

No. Whirlpool also identifies hose installation and excessive suds. A technician must determine whether a component failed.

Can I use Samsung standpipe dimensions?

No. Use the installation instructions for your Whirlpool model; dimensions from another brand are not interchangeable.

Sources: According to the manufacturer. These references are manufacturer guidance, not an independent diagnosis.
Whirlpool US Product Help: Front-load washer error codes — checked 2026-10-22.

Whirlpool washer error codes

Compare the covered codes and their model limits before choosing another procedure.

Open the reference

Related codes and next steps

Use the page for the actual appliance and display.

Related codes & guides

Error code

LG washer · UE

LG washer UE Error Code

Unbalanced load — the drum can't spin evenly.

Easy fix · 10–20 min
Error code

LG washer · OE

LG washer OE Error Code

Drain error — water isn't draining.

Easy fix · 20–30 min
Error code

LG washer · IE

LG washer IE Error Code

Water inlet error — the tub isn't filling.

Easy fix · 10–20 min
Error code

Samsung washer · LC

Samsung washer LC Error Code

Water level or leak error — water is detected where it doesn't belong.

Moderate
Chart

Washers

LG Washer Error Codes

Browse eighteen LG washer code pages, including distinct Ed1/Ed2 detergent warnings and ezDispense Ed5, with model…

Chart

Washers

Washer Error Codes by Brand

One chart for the common washer problems — drain, fill, unbalanced load, door, leak — and the code LG, Samsung and…

Error code

LG washer · dE

LG washer dE Error Code

The door has not closed or locked as required.

Check model first
Error code

LG washer · LE

LG washer LE Error Code

The tub cannot spin; LG identifies overload or an object in the tub as possible reasons.

Check model first
Error code

LG washer · PE

LG washer PE Error Code

LG reports a problem with the water-level sensor.

Call a pro
Error code

LG washer · tE

LG washer tE Error Code

Heating error; LG associates it with the thermistor that senses temperature.

Call a pro
Error code

Samsung washer · dC

Samsung washer dC Error Code

Model-dependent: a door error or an unbalanced-load error.

Check model first
Error code

Samsung washer · Ub

Samsung washer Ub Error Code

An unbalanced load prevented the cycle from completing.

Check model first
Chart

Washers

Samsung Washer Error Codes

Browse fourteen Samsung washer code pages with AC communication, 3C motor and tC sensing, model-dependent 3E meanings…

Chart

Washers

Whirlpool Washer Error Codes

Compare thirteen Whirlpool front-load code pages for water, doors, balance, foam and dispenser messages, with exact…

Error code

LG washer · Sud

LG Washer Sud Error Code

The washer has detected too much foam and is managing an oversudsing condition.

Check model first
Error code

LG washer · PF

LG Washer PF Error Code

Power was interrupted during operation; the display does not identify why the supply was lost.

Check model first
Error code

LG washer · CE

LG Washer CE Error Code

An overcurrent condition has been detected in the motor’s electrical circuit.

Call a pro
Error code

Samsung washer · OC

Samsung Washer OC Error Code

The washer reports an overflow condition: too much water is detected.

Call a pro
Error code

Samsung washer · 4C2

Samsung Washer 4C2 Error Code

The cold-water supply is unexpectedly hot; Samsung identifies reversed hot and cold connections.

Check model first
Error code

Samsung washer · SUd

Samsung Washer SUd Error Code

Excessive suds were detected; the washer pauses to let the foam settle before continuing.

Check model first
Error code

Whirlpool washer · F5 E1

Whirlpool Washer F5 E1 Error Code

Whirlpool identifies this front-load entry as a door-switch condition.

Check model first
Error code

Whirlpool washer · F5 E3

Whirlpool Washer F5 E3 Error Code

The cited Whirlpool front-load guidance says the door is not locking properly.

Check model first
Error code

Whirlpool washer · F7 E1

Whirlpool Washer F7 E1 Error Code

A motor-speed sensing error: the selected cycle speed is not being achieved.

Check model first
Error code

Whirlpool washer · Sud / Sd

Whirlpool Washer Sud / Sd Error Code

Excess suds are interfering with the wash or spin, so the washer adds rinsing and pauses.

Check model first
Error code

LG washer · dHE

LG Washer dHE Error Code

LG identifies a dry-function error on applicable washer-dryer equipment.

Check model first
Error code

LG washer · AE

LG Washer AE Error Code

The covered LG front-load entry reports internal leakage and activation of the leak-protection system.

Call a pro
Error code

LG washer · SE

LG Washer SE Error Code

LG’s front-load support describes SE as a sensor error requiring service if the limited restart does not resolve it.

Call a pro
Error code

Whirlpool washer · F0 E1

Whirlpool Washer F0 E1 Error Code

A load is detected while the Clean Washer maintenance cycle is selected; Whirlpool also lists rL for this condition.

Check model first
Error code

Whirlpool washer · F0 E5

Whirlpool Washer F0 E5 Error Code

The covered front-load washer reports an off-balance load, which can extend the cycle or reduce spin speed.

Check model first
Error code

Whirlpool washer · F8 E2

Whirlpool Washer F8 E2 Error Code

Whirlpool identifies a problem with the front-load washer’s dispenser system.

Check model first
Error code

Whirlpool washer · F8 E3

Whirlpool Washer F8 E3 Error Code

The washer reports an overflow condition involving too much water or foam.

Call a pro
Error code

Whirlpool washer · dET

Whirlpool Washer dET Error Code

The detergent dispenser cartridge is not detected on applicable cartridge-equipped front-load washers.

Check model first
Error code

LG washer · HE

LG Washer HE Error Code

According to LG, HE reports a heater error on the front-load models covered by its US guide.

Check model first
Error code

LG washer · vS

LG Washer vS Error Code

According to LG, vS concerns the vibration sensor; the display can resemble u5 or uS.

Check model first
Error code

Samsung washer · bE2

Samsung Washer bE2 Error Code

Samsung places bE2 in its stuck-button group, but BE2/8E2 means a MEMS sensor error on some models.

Check model first
Error code

Samsung washer · 9C1

Samsung Washer 9C1 Error Code

According to Samsung, 9C1 belongs to the washer electrical-supply irregularity group.

Call a pro
Error code

Samsung washer · ddC

Samsung Washer ddC Error Code

According to Samsung, ddC or dC3 means the Add Door is not detected as closed and locked.

Check model first
Error code

LG washer · Ed1 / Ed2

LG Washer Ed1 / Ed2 Error Code

LG identifies Ed1 and Ed2 as detergent-dispensing warnings, with different pump conditions reported.

Check model first
Error code

LG washer · Ed5

LG Washer Ed5 Error Code

LG identifies Ed5 as a communication problem involving the automatic detergent dispenser and its control system.

Check model first
Error code

Samsung washer · AC

Samsung Washer AC Error Code

Samsung lists AC as a washer communication error; the exact model determines the affected system.

Check model first
Error code

Samsung washer · 3C

Samsung Washer 3C Error Code

Samsung identifies washer 3C as a motor error. It does not by itself identify a failed motor or sensor.

Check model first
Error code

Samsung washer · tC

Samsung Washer tC Error Code

Samsung lists washer tC, tE and tE1 in its temperature-sensor error group.

Check model first

Other codes