Error code
LG dryer · d80
LG dryer d80 Error Code
Exhaust vent about 80% restricted — clean the duct.
Easy fix · 30–60 minWhat it means
Thermistor error — the dryer's temperature sensor reported a problem.
ModerateThe thermistor is the temperature sensor that tells the dryer's control how hot the air is, so it can switch the heat on and off. A tE1 code means the control detected a problem with it. LG's first recommendation is a reset — a temporary bad reading can clear on its own. If tE1 persists after the reset, the sensor or its wiring needs a technician. A related code, tE2, also points to the thermistor; LG notes it usually appears in cold conditions, for example in a cold laundry room or during steam cycles.
| Cause | Difficulty |
|---|---|
| A temporary bad reading from the sensor | Easy fix |
| Faulty thermistor | Call a pro |
| Loose or damaged thermistor wiring or connector | Call a pro |
Unplug the dryer or switch off its breaker. With the power off, press and hold Start/Pause for 5 seconds, as LG describes, then restore power.
Start a short timed dry cycle and watch whether the code returns.
Restricted airflow makes the dryer run hotter; a clean vent rules out one more variable before the service call.
LG’s US list groups tE1 with tE3: both report a problem detected with the thermistor, and both get the same owner response — unplug the dryer or switch off its breaker, hold Start/Pause for 5 seconds while it has no power, restore power and run a cycle, then request a repair if the code returns. tE2 is the cold-conditions variant LG ties to cold vents and steam cycles. TE4, a thermistor reading out of range, goes straight to service. HS is a different sensor altogether: the humidity sensor that decides when clothes are dry, cleaned with a damp cloth.
| Code | LG description | Owner part |
|---|---|---|
| tE1, tE3 | Thermistor problem detected | Power reset with Start/Pause held 5 seconds; repair if it returns |
| tE2 | Thermistor problem, usually in cold conditions | Clear snow, ice and frost from the vent; warm the dryer up |
| TE4 | Thermistor temperature out of range | Service |
| HS | Humidity sensor error | Wipe the sensors below the lint filter |
Airflow is the other half of temperature control. LG reports a clogged exhaust separately, with d80 and the Flow Sense bars, and fire-safety agencies ask owners to clean the lint filter every cycle and keep the vent free of crushing and restrictions. Doing that before the service visit will not repair a failed thermistor, but it removes one variable and is the right routine for any vented dryer.
The thermistor is how the dryer knows how hot the air is. LG says to reset the dryer first; if tE1 returns, the dryer needs repair service. Do not bypass the sensor; have it checked.
Both point to the thermistor. LG notes that tE2 usually shows up in cold conditions, such as an unheated laundry room.
Sources: According to the manufacturer; this is not an independent diagnosis.
LG USA: Dryer — Error Code List — checked 2026-10-26.
U.S. Fire Administration: Clothes Dryer Fire Safety flyer — checked 2026-10-26.
Codes can differ between model generations — check the troubleshooting table in the owner’s manual of your model.
Weigh the repair quote against the age and price of a new unit.
Moisture sensing and routine vent care are separate from the thermistor.
Error code
LG dryer · d80
Exhaust vent about 80% restricted — clean the duct.
Easy fix · 30–60 min
Error code
LG dryer · PS
Power supply error — improper voltage at the power cord.
Call a pro
Error code
Samsung dryer · tC
A temperature or temperature-sensor issue has been detected.
Check model first
Error code
Samsung dryer · HC
Heating error, generally excessive heat; Samsung also notes a low-voltage exception on electric dryers.
Call a pro
Error code
Samsung dryer · dC
A door, latch or door-detection problem.
Check model firstDryers
LG dryer codes by family: door, humidity sensor, temperature sensor, airflow and power, plus the Add Water and Child…
Dryers
Find ten Samsung dryer code pages, including oD dry-time reporting, with model-specific safe checks, service limits…
Guide
Symptom guide
Distinguish no heat from warm but damp clothes, check the model’s cycle settings and accessible lint areas, and leave…
Error code
Samsung dryer · 9C1
Samsung groups 9C1 with supply-voltage warnings; some stacked multi-control installations have a specific software exception.
Call a pro
Error code
Samsung dryer · bE
A control-panel button is being detected as stuck or continuously pressed.
Check model first
Error code
Samsung dryer · AC
Internal dryer components are not communicating with each other as expected.
Call a pro
Error code
Samsung dryer · FC
The dryer reports an invalid power-source frequency; Samsung also lists FE and 1 FC in this group.
Call a pro
Error code
Samsung dryer · 3C
Samsung lists 3C as a dryer motor error, with service required if the documented recovery does not resolve it.
Call a pro
Error code
Samsung dryer · HC2
Samsung lists HC2 as a gas-ignition error; the final 2 distinguishes it from the general HC heating group.
Call a pro
Guide
Symptom guide
A dryer that runs longer needs a check of the cycle, load and drying system. Use safe Samsung and LG references before…
Guide
Symptom guide
A powered dryer that will not start needs a code, Child Lock and door check. Use the Samsung timer test safely and…
Guide
Symptom guide
Read Samsung Vent Blockage test results with the correct model controls, a cool empty drum and safe next steps for…
Guide
Symptom guide
Samsung dryer dn means a firmware download is in progress. Leave power on, wait for the automatic restart and request…
Dryers
Compare covered LG and Samsung dryer warnings by reported system, with separate boundaries for vented, electric, gas and…
Error code
Samsung dryer · oD
Samsung identifies oD as a Dry Time Error and directs owners to a limited recovery followed by service if it returns.
Check model firstThank you! Your feedback helps us make this page better.
Could not send. Please try again.