Find your code

Samsung Dryer Error Codes

Find ten Samsung dryer code pages, including oD dry-time reporting, with model-specific safe checks, service limits and the separate dn keep-power exception.

By ApplianceCodeHQ Editorial Updated

This Samsung US dryer reference covers ten fault-code pages. oD adds the dry-time warning without an invented time threshold or component diagnosis. Temperature, heating, voltage, buttons, communication, frequency, motor and gas-ignition entries retain their own checks. Confirm the exact model and venting or fuel design. The separate dn firmware-download guide remains a keep-power exception to routine recovery advice.

Model and appliance scope

Samsung US digital-display dryers covered by the support code list. Blinking-light models need their own pattern guide. Exhaust checks apply to vented dryers; heat-pump maintenance must follow the exact manual.

Samsung Dryer code reference

CodeMeaningDifficultyFix
tC A temperature or temperature-sensor issue has been detected. Check model first tC page →
HC Heating error, generally excessive heat; Samsung also notes a low-voltage exception on electric dryers. Call a pro HC page →
dC A door, latch or door-detection problem. Check model first dC page →
9C1 Samsung groups 9C1 with supply-voltage warnings; some stacked multi-control installations have a specific software exception. Call a pro 9C1 page →
bE A control-panel button is being detected as stuck or continuously pressed. Check model first bE page →
AC Internal dryer components are not communicating with each other as expected. Call a pro AC page →
FC The dryer reports an invalid power-source frequency; Samsung also lists FE and 1 FC in this group. Call a pro FC page →
3C Samsung lists 3C as a dryer motor error, with service required if the documented recovery does not resolve it. Call a pro 3C page →
HC2 Samsung lists HC2 as a gas-ignition error; the final 2 distinguishes it from the general HC heating group. Call a pro HC2 page →
oD Samsung identifies oD as a Dry Time Error and directs owners to a limited recovery followed by service if it returns. Check model first oD page →

Safe first checks

  1. Record the display before resetting

    Include suffixes and the full model number. Identify the power type for support.

  2. Use accessible maintenance only

    Lint-screen and visible vent checks belong on the temperature/heating path. Laundry in the door opening belongs on the dC path.

  3. Stop on a returning warning

    Use the dedicated page’s service condition rather than repeatedly trying a hot cycle.

How Samsung groups dryer codes

Samsung’s US dryer page sorts its codes into families, and several displays share one meaning: a door problem can read dC, dE, dF, do or d0, and the temperature family includes tC, tS, tE and their variants. Knowing the family tells you which page applies even when your panel shows a variant. The table summarizes the groups as Samsung listed them when we rechecked the page on 2026-10-26; the linked code pages above carry the owner steps and service limits for each.

Samsung US dryer code families (TSG10001006)
FamilyDisplays listedWhat it concerns
Voltage 9C1, 9E, 2E, 9E1 Supply voltage; an electrician measures it
Jammed button bE, bE2, bC2, 6E, 6E2, 6C2 Stuck button on the panel
Door dC, dE, dF, do, d0, 1 DC, 1 dF Door closure or detection
Temperature tS, t5, tC, tO, t0, tE, tE3 and variants Temperature sensing
Heating HC, hE, HC4, 1 HC Heating outside the expected range
Communication AC, Et, AE, EEE and variants Control boards not communicating
Frequency FC, FE, 1 FC Power frequency
Vent test results CLg, C80, C90, Ct, C1 and others Results of a Vent Blockage test
Status dn, CL Firmware download; Child Lock

4C is not on the list. Samsung uses 4C on washers and dishwashers for water supply problems, but its US dryer page does not include a 4C or 4E code. If a dryer seems to show 4C, photograph the full display and check the manual for your exact model before following washer advice. For codes the page does not list, Samsung’s general advice is to power the dryer off for 2–3 minutes, power it on, restart the cycle and contact Samsung if the code returns.

How to clean a dryer vent safely

Vent test results and slow drying both start with the lint filter, the duct and the outdoor flap.

Read the guide

Frequently asked questions

Does dryer dC mean an unbalanced load?

The cited dryer entry concerns the door. Some Samsung washers use dC for imbalance, which is a different appliance lookup.

Does HC always identify a failed heater?

No. Samsung describes a heating warning and a supply-voltage exception on electric dryers; professional diagnosis may be necessary.

Sources: According to the manufacturer; exact model instructions take precedence.
Samsung US: Dryer displays an error code — checked 2026-10-26.
Samsung US: Clothes are not dry after using the dryer — checked 2026-10-22.

Symptom guides and related references

Continue with the relevant symptom or compare a repair quote after diagnosis.

Drying symptoms and test results

More covered laundry codes and guidance

Related codes & guides

Error code

LG dryer · d80

LG dryer d80 Error Code

Exhaust vent about 80% restricted — clean the duct.

Easy fix · 30–60 min
Error code

LG dryer · tE1

LG dryer tE1 Error Code

Thermistor error — the dryer's temperature sensor reported a problem.

Moderate
Error code

LG dryer · PS

LG dryer PS Error Code

Power supply error — improper voltage at the power cord.

Call a pro
Error code

Samsung dryer · tC

Samsung dryer tC Error Code

A temperature or temperature-sensor issue has been detected.

Check model first
Error code

Samsung dryer · HC

Samsung dryer HC Error Code

Heating error, generally excessive heat; Samsung also notes a low-voltage exception on electric dryers.

Call a pro
Chart

Dryers

LG Dryer Error Codes

LG dryer codes by family: door, humidity sensor, temperature sensor, airflow and power, plus the Add Water and Child…

Error code

Samsung dryer · 9C1

Samsung Dryer 9C1 Error Code

Samsung groups 9C1 with supply-voltage warnings; some stacked multi-control installations have a specific software exception.

Call a pro
Error code

Samsung dryer · bE

Samsung Dryer bE Error Code

A control-panel button is being detected as stuck or continuously pressed.

Check model first
Error code

Samsung dryer · AC

Samsung Dryer AC Error Code

Internal dryer components are not communicating with each other as expected.

Call a pro
Error code

Samsung dryer · FC

Samsung Dryer FC Error Code

The dryer reports an invalid power-source frequency; Samsung also lists FE and 1 FC in this group.

Call a pro
Error code

Samsung dryer · 3C

Samsung Dryer 3C Error Code

Samsung lists 3C as a dryer motor error, with service required if the documented recovery does not resolve it.

Call a pro
Error code

Samsung dryer · HC2

Samsung Dryer HC2 Error Code

Samsung lists HC2 as a gas-ignition error; the final 2 distinguishes it from the general HC heating group.

Call a pro
Chart

Dryers

Dryer Error Codes by Brand

Compare covered LG and Samsung dryer warnings by reported system, with separate boundaries for vented, electric, gas and…

Error code

Samsung dryer · oD

Samsung Dryer oD Error Code

Samsung identifies oD as a Dry Time Error and directs owners to a limited recovery followed by service if it returns.

Check model first