Calculator
Tool
Repair vs Replace Calculator
Enter the appliance age, its expected lifespan, the repair quote and the price of a new unit to see whether the fix is…
PS is LG's power supply code for dryers. It means the dryer detected improper voltage within the power cord. LG names one typical cause: the white and red wires reversed on the dryer's terminal block — the connection point at the back where the power cord is attached when the dryer is installed. That is why PS can show up right after installation or after the cord was replaced. Because the fix involves 240-volt wiring, this is not an owner repair.
| Cause | Difficulty |
|---|---|
| Power cord wires connected to the wrong terminals on the terminal block | Call a pro |
| Loose connection at the terminal block or the outlet | Call a pro |
| A problem with the household circuit or breaker | Call a pro |
Do not keep restarting it while the code is showing.
At the panel, check that the dryer's breaker is fully on; if it tripped, reset it once.
If the code appeared after the dryer was installed or the cord was changed, tell the installer or a technician — the terminal block wiring is the first thing to check.
LG’s US list has two codes for electrical supply on dryers, and they point to different places. PS means improper voltage within the power cord, with reversed white and red wires at the terminal block as LG’s typical example — a connection made when the dryer was installed or the cord replaced. nP means no current is being detected at the heater and, according to LG, usually points to the home’s wiring. For both, LG’s owner checks stop at the outlet and the breaker: a grounded 240 V outlet, and the breaker switched off for 10 seconds and back on.
| Code | LG description | Who checks it |
|---|---|---|
| PS | Improper voltage within the power cord | Installer or technician for the cord connection; electrician for the outlet |
| nP | No current detected at the heater, usually home wiring | Electrician for the outlet voltage; LG service if the supply is fine |
When you call, say whether the code appeared after installation, after the cord was replaced or after electrical work in the house, and whether the dryer turns but stays cold. That history is what lets the installer, the electrician or LG service decide who goes first. It also keeps the conversation away from lint and vents, which do not cause PS.
Checking the breaker is safe. Rewiring the power cord at the terminal block is a job for a qualified technician or electrician.
LG names a new installation as a typical case: the power cord was attached to the terminal block with the white and red wires reversed.
Sources: According to the manufacturer; this is not an independent diagnosis.
LG USA: Dryer — Error Code List — checked 2026-10-26.
U.S. Fire Administration: Clothes Dryer Fire Safety flyer — checked 2026-10-26.
Codes can differ between model generations — check the troubleshooting table in the owner’s manual of your model.
When a fix is worth the money and when a new unit makes more sense.
The other LG power code and a routine that keeps any dryer safer.
Calculator
Tool
Enter the appliance age, its expected lifespan, the repair quote and the price of a new unit to see whether the fix is…
Error code
LG dryer · d80
Exhaust vent about 80% restricted — clean the duct.
Easy fix · 30–60 min
Error code
LG dryer · tE1
Thermistor error — the dryer's temperature sensor reported a problem.
Moderate
Error code
Samsung dryer · tC
A temperature or temperature-sensor issue has been detected.
Check model first
Error code
Samsung dryer · HC
Heating error, generally excessive heat; Samsung also notes a low-voltage exception on electric dryers.
Call a pro
Error code
Samsung dryer · dC
A door, latch or door-detection problem.
Check model firstDryers
LG dryer codes by family: door, humidity sensor, temperature sensor, airflow and power, plus the Add Water and Child…
Dryers
Find ten Samsung dryer code pages, including oD dry-time reporting, with model-specific safe checks, service limits…
Guide
Symptom guide
Distinguish no heat from warm but damp clothes, check the model’s cycle settings and accessible lint areas, and leave…
Error code
Samsung dryer · 9C1
Samsung groups 9C1 with supply-voltage warnings; some stacked multi-control installations have a specific software exception.
Call a pro
Error code
Samsung dryer · bE
A control-panel button is being detected as stuck or continuously pressed.
Check model first
Error code
Samsung dryer · AC
Internal dryer components are not communicating with each other as expected.
Call a pro
Error code
Samsung dryer · FC
The dryer reports an invalid power-source frequency; Samsung also lists FE and 1 FC in this group.
Call a pro
Error code
Samsung dryer · 3C
Samsung lists 3C as a dryer motor error, with service required if the documented recovery does not resolve it.
Call a pro
Error code
Samsung dryer · HC2
Samsung lists HC2 as a gas-ignition error; the final 2 distinguishes it from the general HC heating group.
Call a pro
Guide
Symptom guide
A dryer that runs longer needs a check of the cycle, load and drying system. Use safe Samsung and LG references before…
Guide
Symptom guide
A powered dryer that will not start needs a code, Child Lock and door check. Use the Samsung timer test safely and…
Guide
Symptom guide
Read Samsung Vent Blockage test results with the correct model controls, a cool empty drum and safe next steps for…
Guide
Symptom guide
Samsung dryer dn means a firmware download is in progress. Leave power on, wait for the automatic restart and request…
Dryers
Compare covered LG and Samsung dryer warnings by reported system, with separate boundaries for vented, electric, gas and…
Error code
Samsung dryer · oD
Samsung identifies oD as a Dry Time Error and directs owners to a limited recovery followed by service if it returns.
Check model firstThank you! Your feedback helps us make this page better.
Could not send. Please try again.